Fiber Optic Termination Experts

New Products

SORT BY:

Page:

1 2 3 4 5 6 7 8

Displaying 1 - 10 of 75

1.60mm Light Source Adapter Cap
PART#: 0799-2092
new mil com

The 1.60mm blue adapter cap is designed to work with the 0700-8500 FiberSure Light Source. Works with the M29504/4/5/6/7 termini.

Aviation Fiber Optic Inspection & Cleaning Kit
PART#: 0741-8010
new com

The Aviation Fiber Optic Inspection and Cleaning Kit was designed with input from the Commercial Air Transport Industry. This kit is designed to inspect and clean the most common types of fiber optic connectors found onboard the aircraft.
This kit will allow the technician to inspect and clean the following fiber optic connectors/termini:
* M38999 Plug Connectors
* ARINC 801 Circular Connectors
* ARINC 600 Rectangular Connectors
* EPX Rectangular Connectors
* Quadrax Size 8 Connectors
* ARINC 801 Termini
* EN 4531 Termini
* M29504/04 Pin Termini
* M295-4/05 Socket Termini
* ST Connectors
* SC Connectors
* FC Connectors
* LC Connectors

Aviation Fiber Optic Inspection & Cleaning Kit
PART#: 0741-8015
new com

This kit is designed to test the fiber optic endface using a laptop computer and software that will give the technician a Pass or Fail inspection result. The software also allows the technician to capture a picture of the endface and save the test results. The kit will also clean the most common types of fiber optic connectors found onboard the aircraft.

This kit will allow the technician to inspect and clean the following fiber optic connectors/termini:
* M38999 Plug Connectors
* ARINC 801 Circular Connectors
* ARINC 600 Rectangular Connectors
* EPX Rectangular Connectors
* Quadrex Size 8 Connectors
* ARINC 801 Termini
* EN 4531 Termini
* M29504/04 Pin Termini
* M29504/05 Socket Termini
* ST Connectors
* SC Connectors
* FC Connectors
* LC Connectors

Aviation Programmable Oven
PART#: 0721-1305
new mil com

The 0721-1305 Aviation Programmable Oven is designed to cure aerospace fiber optic epoxies using a 4 step temperature cure schedule. The oven is pre-programmed with the NAVAIR cure schedule for Epo Tek 353ND epoxy. The cure schedule can be easily changed to meet your epoxy cure temperature requirements. The ramp time, soak time, and cure temperature can be changed within the cure schedule program.
The oven comes with our new redesigned heating block which will accommodate up to 36 fiber optic connectors/termini at the same time. The block will cure 12 of the ST,SC, FC or LC connectors and 24 fiber optic termini.
The following is a list of the fiber optic termini that will fit in the heating block:
• M29504/04 Pins
• M29504/05 Sockets
• M29504/14 Pins
• M29504/15 Sockets
• ARINC 801
• Elio (EN 4531)

Aviation Termination Kit with Programmable Oven
PART#: 0741-8001
new mil

The 0741-8000 Aviation Termination Kit is designed to terminate and/or repair M29504/4 and M29504/5 termini for circular M38999 connectors.
This kit will also terminate the ARINC 801 termini, Elio (EN4531) termini, the M83522/16 ST connectors as well as the approved Commercial Off the Shelf (COTS) ST, SC connectors, and LC connectors. This kit contains all of the tooling and consumables required to completely terminate all of the termini and connectors listed above for installation of fiber optics in harsh environments onboard the aircraft. The kit also contains the programmable curing oven that allows for a 4 step temperature cure schedule.

This kit meets and exceeds all of the current military Aviation Termination Kit requirements, and the rugged hard shell
case meets the MIL–STD–810F requirements.

Biconic C-Clip Install Tool
PART#: 0701-6040

NSN#: 5120-01-564-3564

new mil

The 0701-6040 Biconic C-Clip Tool is used to install the c-clips onto Biconic termini.

Biconic Cure Adapter
PART#: 0700-1485

NSN#: 5935-01-562-0484

new mil

The 0700-1485 Biconic Cure Adapter is manufactured from aluminum for better heat transfer from the oven heater block. In the past cure adapters were made from white Delrin material which could hinder the curing of the epoxy inside the Biconic termini.

Biconic Digital Length Gauge
PART#: 0701-6035

NSN#: 6625-01-562-0546

new mil

The 0701-6035 Biconic Digital Length Gauge is designed to accurately measure the height of the Biconic support cone during the polishing process. The gauge reads in both inches and millimeters.

Biconic Insert Tool
PART#: 0701-6060

NSN#: 5120-01-564-3561

new mil

The 0701-6060 is used to intall and remove the dual channel Biconic insert for the TFOCA (FG) connector. It threads into the front insert holes.

Biconic Installation Fixture
PART#: 0701-6090

NSN#: 3465-01-562-0553

new mil

The 0701-6090 Biconic Installation Fixture is used during the assembly and disassembly of the dual channel TFOCA (FG) connector. The fixture allows the user to compress the springs on the Biconic termini for easy installation or removal of the c-clips.

Legend: com = Commercial | mil = Military | new = New Product

Page:

1 2 3 4 5 6 7 8

Displaying 1 - 10 of 75


Admin	Field Services	Commercial Tools & Tool Kits	Military Tools & Tool Kits	All Tools & Tool Kits
Home Company News and Events Employment Request Information NSN MSDS Catalogs Directions Partners	Overview Qualifications Portfolio Commercial Connector Terminations Military Connector Terminations Testing and Troubleshooting Fusion and Mechanical Splicing Blown Optical Fiber (BOF) Technical Support	New Commercial Products Accessories Connectors Consumables Test and Inspection Equipment Ovens and Accessories Kits Tools	New Military Products Accessories Connectors Consumables Test and Inspection Equipment Kits Tools	New Products Accessories Connectors Consumables Test and Inspection Equipment Ovens and Accessories Kits Tools MQJs